Enerdrive 600Ah Caravan 3000W Bundle & Simarine Pico+ Display Panel Mount Black

Enerdrive 600Ah Caravan 3000W Bundle & Simarine Pico+ Display Panel Mount Black, 5 Year Warranty. Pack Includes: Enerdrive ePOWER B-TEC 300Ah Lithium Battery, 2 x EPL-300BT-12V-G2 Enerdrive ePRO Combi 3000W Inverter Charger, EPC-3000-12-KIT Enerdrive Cable Kit for 3000W Lithium System, EPL-3000W-CABLE-KIT Enerdrive ePRO Universal Remote Control Panel, 5095500 Enerdrive DC2DC Battery Charger – 12V 40A, EN3DC40+ Enerdrive MPPT 12/24V 40A Solar Controller with Display, EN43540 Enerdrive Class-T Fuseholder 50V/225A-400A, DCM-5073850 BS-5121B Enerdrive EN-RCB50 Surface Mount Resettable Breaker – 50amp, EN-RCB50 Enerdrive EN-RCB60 Surface Mount Resettable Breaker – 60amp, EN-RCB60 Enerdrive EN-RCB70 Surface Mount Resettable Breaker -70amp, EN-RCB70 Enerdrive 95mm2 x 200mm Battery Parallel Cable Kit, Positive & Negative, to suit 300Ah Batteries, ENC-KIT-PARALLEL-95-01 Battery Monitor Option: No Monitor Enerdrive ePRO Plus Battery Monitor, EN55050 SI-PICO-3, SI-SC303, SI-SCQ50 Solar Panel Option: No Solar Panels Enerdrive 180W Mono Crystalline Fixed Solar Panel, Black, 2 x SP-EN180W-B Enerdrive 180W Mono Crystalline Fixed Solar Panel, Black, 4 x SP-EN180W-B Enerdrive ePOWER B-TEC 300Ah Lithium Battery. Available in 12v 300Ah capacity, the Enerdrive B-TEC G2 lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity. Key Features: New design BMS Max discharge current 250A (15mins) – 200A continuous Max charge current 190A (30mins) Can be connected in parallel (up to 4 batteries) Built in flat battery reset button Includes mounting tray and 2 straps Communication ports (RS485) for future integration 5 year warranty & lifetime tech support Smart Phone Monitoring System The Enerdrive B-TEC G2 battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information; Battery Capacity Battery Voltage Battery Current (Amps) Battery State of Charge (SOC) Battery State of Health (SOH) Battery Status Individual Cell Voltage Battery Temperature Battery Cycles Battery Alarms Battery Event Information Battery Management System The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery. Size & Weight Savings Lithium v AGM Capacities: 100Ah Lithium = 160Ah AGM 125Ah Lithium = 200Ah AGM 200Ah Lithium G2 = 320Ah AGM 300Ah Lithium G2 = 480Ah AGM (Based on standard depth of discharge for both Lithium (80%) and AGM (50%). The Enerdrive B-TEC G2 battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative. The Enerdrive B-TEC G2 battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity. The New Generation 2 B-TEC So, How does the New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery measure up against it original predecessor? Let’s have a look. Dimension Original Generation 2 Length 519mm 521mm Width 273mm 280mm Height 222mm 253mm Also included for free is a metal battery tray and hold down strap to complete the installation process. The G2 now incorporates a “Built-In Reset Button” making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery. The new G2 also includes a RS485 communications port located on the top of the battery. This port allows for integration onto other CanBus systems for data monitoring and recording. The New Enerdrive Generation 2 (G2) B-TEC 300Ah Lithium Battery now comes with a 5 year warranty, giving you peace of mind that this product will keep you covered. With over 8 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup. With over 4000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications. Please Note; The G2 battery is capable to be paralleled to a second G2 battery. For maximum performance and lifespan of your G2 battery, no more than 2 batteries should be connected together to increase your overall capacity. Overall loads when paralleled should not exceed the current limits of a single batteries BMS. The G2 300Ah battery is able to accept a maximum inverter capacity of 3000W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery. If you are requiring a battery system larger than the Enerdrive B-TEC G2 battery, please look at the Enerdrive Pro Series Power Pack Systems which can offer multiple parallel and series connections with Active Cell Balancing Protection across the entire pack. Enerdrive ePRO Inverter / Charger 3000W. The main task of the ePRO Combi Inverter Charger is to act as an uninterruptible AC power supply (UPS). In case of a grid/generator failure or disconnection, the ePRO Combi immediately stops charging the battery, releases the AC transfer switch and activates the inverter which takes over the supply to the connected loads. All this is achieved so fast, that even very critical loads like computers will continue to operate without any problems. In case the grid/generator is reconnected again and the voltage and frequency are within acceptable limits, the ePRO Combi activates the AC transfer switch and battery charger again, while deactivating the inverter. The connected loads are now supplied again by the grid/generator without any interruption. Available in 12v, 24v or 48v models and ranging in sizes from 1600-3500w inverter output and 35-120A charger output, the ePRO Combi has a unit to suit nearly any application. Complete with 5 Year warranty. Additionally, the ePRO Inverter Charger offers features like : AC Input Power Boost, which temporarily assists weak AC input sources when the connected load needs more power than available from the grid or generator. AC Input Current Limit, which limits the maximum current consumed from the AC input source by the ePRO Combi. This limit is user adjustable. Power Factor Corrected AC Input, which optimizes energy efficiency and makes sure that the maximum amount of charging current is available from your AC source. Intelligent 4-stage charge programs, user programmable to fit any battery type. Fully programmable inverter, transfer switch and battery charger parameters, using the Dashboard for Windows software. Programmable alarm relay, for optimal control of external devices like generator starting or selective load disconnection. Freely assignable trigger input, which allows the user to control the ePRO Combi by external events. Temperature controlled fans, to guarantee silent operation under less than full load conditions. Temperature compensated battery charging, using the standard supplied battery temperature sensor for maximum battery lifetimes. When installation space is at a premium, but maximum performance is required then look no further than the ePRO Combi range. With so many internal features the ePRO Combi will provide you with all the requirements for on-board power along with: AC Input Power Boost – The ePRO Combi is capable of temporarily assisting weak AC input sources when more power is needed than available (i.e. from small generators). This is beneficial when larger loads than both the generator or the inverter on their own could support; so let the ePRO Combi combine both of the AC sources for maximum load support capability. AC Input Current Limit – For those times when you have limited AC supply (i.e. portable generators), you can set the ePRO Combi to only charge at a maximum rate. Alarm Output Relays – Providing full configuration options for the alarm contacts PLUS convert external trigger commands into a number of ePRO Combi status changes. Also available on the larger 2000-3500w Combi’s are two fully configurable 16A 230v alarm relay outputs for controlling large AC loads like air conditioning. Along with two unique trigger inputs, it gives the end user virtually unparalleled control of their Enerdrive ePRO “Power Station”. Enerdrive Cable Kit for 3000W Lithium System. This cable kit is required for the Enerdrive ePRO Inverter / Charger 3000W . Enerdrive ePRO Combi Universal Remote Control Panel to suit Enerdrive ePRO Battery Chargers. The Universal Remote Control Panel can read all available parameters from your ePRO charger – charging current, output voltage, charge stage and so on. Features: Solar Power Systems Industrial Systems Recreational Vehicles Marine Systems Commercial Work Vehicles Reads avaliable parameters Enerdrive ePOWER 12V 40A DC to DC Battery Charger Designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems. The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the main/house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays. During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads. 12V 40A DC2DC Battery Charger Features Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in Enerdrives AC mains ePOWER battery charger including a specific lithium charging profile 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging PRO TIPS: Common accessories to go with this DC to DC charger are the 60Amp & 70Amp breakers, also the 3 pre-wired & fused charging cables. These are available in the Accessory List above to add as optional extras, please see the product manual & drawings for the connection. You will require a ratchet crimping tool for this cable kit. PLEASE CLICK HERE to find our tool range. Multistage Charging Process The ePOWER DC2DC+ Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries. The ePOWER DC2DC+ Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery bank permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array. As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC+ smart charger delivers three primary charge stages. Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible. Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge. Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply. Smart Charging Feature The ePOWER DC2DC+ Battery Charger will regulate its output based on the loads connected to your battery bank. This function is important to maintain the life of your battery bank as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC+ Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so. Maximising your Solar Harvest using the DC2DC+ The Solar Input on the DC2DC+ unit has a maximum rated INPUT current of 30amps. This means it is optimised for using higher voltage ‘grid’ type modules for best output performance. The maximum achievable output using standard 20Voc solar modules will be approx 35amps @ 14.4Vdc. Panel Array Rated Wattage & Volts Open Circuit Rating Estimated DC Amps Output (## See Below) 1 150watt @ 20Voc 150watts 10 1 200watt @ 43Voc 200watts 13 2 150watt @ 20Voc 300watts 21 2 200watt @ 43Voc 400watts 27 3 150watt @ 20Voc 450watts 31 3 200watt @ 43Voc 600watts 42 4 150watt @ 20Voc 600watts 35* 4 200watt @ 43Voc 800watts 47** 5 150watt @ 20Voc 1000watts Not Recommend 5 200watt @ 43Voc 1000watts Not Recommend * Maximum achievable output on the DC2DC+ unit when using 20Voc Solar Panels will be the approx 35amps. ** Maximum achievable output on the DC2DC+ unit when using 43Voc Solar Panels will be the approx 47amps. ## IMPORTANT NOTE: Estimated Amps Output is quoted based upon PERFECT Solar conditions including Sun Angle, Panel Mounting angle and Orientation to the sun. It needs to be noted that panel performance alters dramatically between Summer and Winter periods and actual performance may be impossible to predict. Click here for this DC to DC Charger with a full wiring kit, including resettable circuit breakers! For In Vehicle & Marine Wiring Diagram, click below: For Towed Vehicle Wiring Diagram, click below: For Pre-Wired Cable Kits (input only), click below: Enerdrive MPPT 12/24V 40A Solar Controller with Display. The Enerdrive MPPT Solar Controllers adopt the advanced MPPT control algorithm, it can minimize the maximum power point loss rate and loss time, quickly track the maximum power point (MPP) of the PV array and obtain the maximum energy from solar array under any conditions; and it can increase the ratio of energy utilization in the solar system by 20%-30% compared with PWM charging method. The Enerdrive MPPT Solar Controllers has self-adaptive three-stage charging mode based on digital control circuit, which can effectively prolong the lifespan of batteries and ­significantly improve the system performance. It also has comprehensive electronic protection for overcharge, over discharge, PV & battery reverse polarity. This controller can be widely used for RV, Marine, remote offgrid monitoring and many other applications. IP33 Ingress protection and isolated RS485 design further improves the controller’s reliability and meet the different application requirements. Enerdrive MPPT Solar Controller Features: CE certification (LVD EN/IEC62109,EMC EN61000-6-1/3) LCD display Advanced MPPT technology & ultra-fast tracking speed guarantee’s tracking efficiency up to 99.5% Maximum DC/DC transfer efficiency is as high as 98.6%. Advanced MPPT control algorithm to minimize the MPP lost rate and lost time Accurate recognition and tracking of multi-peaks maximum power point Wide MPP operating voltage range Support lead-acid and lithium batteries Real-time energy statistics function Power reduction automatically over temperature value Multiple load work modes Comprehensive electronic protection IP33 Ingress protection Comms port included for future applications Enerdrive Class-T Fuseholder 50V/225A-400A. The DC Modular high current busbars are used to distribute high DC currents to a number of connected cables, or other DC Modular family members. The solid and compact design, as well as the possibility to link up multiple busbars on a fixed grid, make these products the best choice for all professional DC power systems. Enerdrive EN-RCB60 Surface Mount Resettable Breaker -60amp . Enerdrive's affordable range of surface mount circuit breaker while keeping with the high quality that our customers have come to expect. Unit between 25-70amp have 1/4” studs while the larger units 80—150amp have the larger 3/8” studs for Quality DC connections. Please Note: Check the Enerdrive Charger Manual for recommended Breaker & Cable sizing. Enerdrive EN-RCB70 Surface Mount Resettable Breaker -70amp . Enerdrive have just released a affordable range of surface mount circuit breaker while keeping with the high quality that our customers have come to expect. Units between 25-70amp have 1/4” studs while the larger units 80—150amp have the larger 3/8” studs for Quality DC connections. Please Note: Check the Enerdrive Charger Manual for recommended Breaker & Cable sizing. Enerdrive 95mm2 x 200mm Battery Parallel Cable Kit, Positive & Negative, to suit 300Ah Batteries. Enerdrive Parallel cable kit to connect 2 x 300Ah batteries together. Enerdrive ePRO PLUS Battery Monitor. Complete battery status information at a glance (%, V, A, Ah, W, h:m, °C) Supports up to three battery banks (12V, 24V and 48V) Very simple ‘Plug and Play’ installation Perfect integration with Enerdrive DC Modular products The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4). The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit. Simarine by Enerdrive Battery Shunt 300A 2 x Volt 1 Resist. Battery Shunt to suit Simarine Pico Monitors 2 x Volt 1x Resistance Enerdrive 180W Mono Crystalline Fixed Solar Panel, Black. Enerdrive solar panels are typically around 20+vdc open circuit. Suited to 12v installations (or 24v by series connections of panels) A fl
Read more