Enerdrive 4WD Canopy Explorer System with ePRO Plus Battery Monitor, Driver Side Installation

Enerdrive 4WD Canopy Explorer System with 40A DC2DC Charger & ePRO Plus Battery Monitor, Driver Side Installation, 5 Year Warranty. Enerdrive have created three compact power solutions to operate all of the electrical equipment that is located in 4WD canopies, including a simple fridge or lights setup to a full on power station. There are three models in this range: The Explorer, The Traveller and The Adventurer, all of which can be paired with any brand or model of battery including Wet Sealed, AGM, Gel and Lithium! The Explorer system is designed for the end user only requiring a minimum power option in a neat package. The Explorer consists of the following items Enerdrive ePOWER DC2DC40+ Vehicle/Solar Charger 1 x Battery Monitor (customer has the choice between a ePRO Plus battery monitor, Simarine battery monitor or Simarine Battery Monitor & Quad Shunt Module) 4x Pre-wired Circuit Breakers for main power equipment 4 x Contura switches for Lights & Auxiliary loads Pre-wired Battery & Fridge Anderson Plugs ( Explorer & Traveller only ) Your choice of Twin USB 2.4A Hi Amp sockets to charge your mobile devices (standard) or mix it up with a 12v Output Socket (available upon request Battery Reset button for kick starting your flat battery from the DC2DC Charger Please note, each system either comes standard with an ePRO Plus battery monitor (as shown in images) and customers have the choice to upgrade to a Simarine battery monitor or Simarine Battery Monitor & Quad Shunt Module for an additional cost (you can make this selection above before adding product to cart). All systems are pre-wired by Enerdrive where possible so the only cabling required at installation time is load outputs, battery connection, & vehicle/solar/tank inputs All systems are built into a unique compact box arrangement and designed to mount on either the front or rear bulkheads of the vehicles canopy. The systems are available in either passenger side or drivers side installation. Any brand of battery is suitable from Wet Sealed, AGM, Gel and Lithium. Enerdrive are proud to bring to market this innovative design that can be installed by the canopy manufacturer or end user in a neat one piece installation. Please note, location of installation (driver's side or passenger's side of the vehicle) must be specified upon ordering. Enerdrive ePOWER 12V 40A DC to DC Battery Charger: Enerdrive ePOWER 12V 40A DC to DC Battery Charger designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems. The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. 12V 40A DC2DC Battery Charger Features Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging For In Vehicle & Marine Wiring Diagram, click below: For Towed Vehicle Wiring Diagram, click below: Enerdrive ePRO PLUS Battery Monitor, 5 Year Warranty. Complete battery status information at a glance (%, V, A, Ah, W, h:m, °C) Supports up to three battery banks (12V, 24V and 48V) Very simple ‘Plug and Play’ installation Perfect integration with Enerdrive DC Modular products The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4). The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit. Other Battery Monitor Options: For consumers who want to upgrade to a Simarine battery monitor, there are two options: Simarine Pico+ Display Panel Mount Black Simarine Pico+ Display Panel Mount Black & Quad Shunt Module (4 x 50A Input Current & 1 x Relay Output 1A) Simarine Pico sets new standards for marine battery and tank monitors in fields of design, functionality, connectivity and ease of use. The IP67 casing of the main unit is CNC-milled from a single piece of high quality 6000 series anodized aluminium (corrosion-proof). The 3.5’’ inch IPS LCD display is optically bonded with Anti-Reflective Gorilla Glass®. Enerdrive's unique Real Time Battery Health™ algorithm ensures very precise battery state of charge and health measurements.
Read more