Enerdrive DIY 40A AC and 40A DC2DC Charging Board – Pre Wired

Enerdrive DIY 40A AC and 40A DC2DC Charging Board – Pre Wired, 5 Year Warranty. The Enerdrive DIY 40A AC and 40 DC2DC Charging Board is perfect for the DIY installer seeking a quality solution at a budget price! This system comprises of the: Enerdrive DC2DC Battery Charger Enerdrive 40A AC Battery Charger Enerdrive ePRO Plus Battery Monitor Quality midi fuse assemblies Fuse block distribution ready for accessory load circuits Master circuit Breakers ready for an additional Inverter up to 2000W Inverter Andreson connectors for ease of installation. Available with or without an accessory box including 3 switches and provision to mount your battery monitor display. Compare all the DIY Installation Kit models below: Items Included eSYS-C eSYS-D eSYS-E eSYS-F eSYS-G eSYS-H eSYS-I eSYS-J K-DIY-Board-01 ePOWER AC 40Amp 230v Charger * * * * * * ePOWER AC 60Amp 230v Charger * * * ePOWER DC2DC 40+ Charger (Vehicle/Solar) * * * * * * * * * Morningstar Tristar PWM-45A Solar Controller * * * ePRO Plus 500A Battery Monitor * * * * * with Remote Display Simarine Pico LCD WIFI Monitoring Screen * * * * Simarine SC303 300A Main Battery Shunt * * * * Simarine SCQ25T Individual Load/Charge Module * * * Simarine SCQ50 Individual Load/Charge Module * * * * 3 Stud Main Negative Bus Bar * * * * * * * * * 40A Low Battery Cutout * * * * * * * * Main System Circuit Breaker 120A * * * * * * Main System Circuit Breaker 200A * * * Inverter Circuit Breaker 200A * * * * * * * * * Solar Input Positive Circuit Breaker 40A * * * * * * Solar Input Positive Circuit Breaker 60A * * * * * * * ePOWER DC2DC 60A Output Fuse Connection * * * * * * * * * ePOWER AC Charger 50A Output Fuse Connection * * * * * * ePOWER AC Charger 70A Output Fuse Connection * * * 1 x 30A Load Output Fuse Connections * * 2 x 30A Load Output Fuse Connections * * * * 50A Load Output Fuse Connection * * 24hr Critical Load 4 Circuit "Wedge" Fuse Block * * * 24hr Critical Load 8 Circuit "Wedge" Fuse Block * Main 6 Circuit "Wedge" Fuse Block * * * with Negative Bus and Cover Main 12 Circuit "Wedge" Fuse Block * * with Negative Bus and Cover ePOWER 2000W AC Transfer Inverter * * Battery Restart Switch (Lithium Batteries) * * * * * 12mm Black Plastic Mounting Board. * * * * * * * * * Water & Rot Resistance 175A Anderson Plug (Inverter) * 50A Anderson Plug (Solar Input) * 50A Anderson Plug (Vehicle Input) * Dimensions 1185L x 380W x 130Dmm 600L x 490W x 100Dmm 600L x 490W x 100Dmm 1185L x 380W x 130Dmm 790L x 380W x 100Dmm 1195L x 380W x 111Dmm 1195L x 380W x 111Dmm 920L x 380W x 111Dmm 580L x 580W x 100Dmm Weight 23kg 14kg 14kg 23kg 16kg 17kg 16.5kg 17kg 14kg (*) Indicates Standard Fitment Enerdrive ePOWER 12V 40A DC to DC Battery Charger: Enerdrive ePOWER 12V 40A DC to DC Battery Charger designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems. The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. 12V 40A DC2DC Battery Charger Features Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging For In Vehicle & Marine Wiring Diagram, click below: For Towed Vehicle Wiring Diagram, click below: Enerdrive ePOWER 40A Battery Charger: The Enerdrive ePOWER 40A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently. As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank). 40A Battery Charger Features: Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks. Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three. Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3. Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator). Smart Charging: The ePOWER 40A battery charger will regulate its output based on the loads connected to your battery banks. Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz. LED Display: Easy to use “set and select” menu along with scrolling charger status. Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours. Temperature Sensor: Battery temperature sensor included with 3 meter cable. 5 Year Warranty from an Australian company renowned for customer support. Enerdrive ePRO PLUS Battery Monitor: Complete battery status information at a glance (%, V, A, Ah, W, h:m, °C) Supports up to three battery banks (12V, 24V and 48V) Very simple ‘Plug and Play’ installation Perfect integration with Enerdrive DC Modular products The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4). The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit. Enerdrive Accessories Box with ePro Plus Battery Monitor and Switches, Not Pre-Wired: The Enerdrive Accessories Box comprises of an ePRO Plus Battery Monitor, three switches and the provision to mount your battery monitor display. If you choose to purchase the board with the accessories box, the accessories box will be included in your package but not mounted and not pre wired. There is a space on the board to mount the accessories box, or you may want to mount it elsewhere in your vehicle.
Read more