Enerdrive DIY 40A AC and 40A DC2DC Charging Board – Pre Wired with Enerdrive Accessories Box

Enerdrive DIY 40A AC and 40 DC2DC Charging Board – Pre Wired with Enerdrive Accessories Box, 5 Year Warranty. The Enerdrive DIY 40A AC and 40 DC2DC Charging Board is perfect for the DIY installer seeking a quality solution at a budget price! This system comprises of the: Enerdrive DC2DC Battery Charger Enerdrive 40A AC Battery Charger Enerdrive ePRO Plus Battery Monitor Quality midi fuse assemblies Fuse block distribution ready for accessory load circuits Master circuit Breakers ready for an additional Inverter up to 2000W Inverter Andreson connectors for ease of installation. Available with or without an accessory box including 3 switches and provision to mount your battery monitor display. Enerdrive ePOWER 12V 40A DC to DC Battery Charger: Enerdrive ePOWER 12V 40A DC to DC Battery Charger designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems. The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. 12V 40A DC2DC Battery Charger Features Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging For In Vehicle & Marine Wiring Diagram, click below: For Towed Vehicle Wiring Diagram, click below: Enerdrive ePOWER 40A Battery Charger: The Enerdrive ePOWER 40A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently. As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank). 40A Battery Charger Features: Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks. Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three. Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3. Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator). Smart Charging: The ePOWER 40A battery charger will regulate its output based on the loads connected to your battery banks. Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz. LED Display: Easy to use “set and select” menu along with scrolling charger status. Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours. Temperature Sensor: Battery temperature sensor included with 3 meter cable. 5 Year Warranty from an Australian company renowned for customer support. Enerdrive ePRO PLUS Battery Monitor: Complete battery status information at a glance (%, V, A, Ah, W, h:m, °C) Supports up to three battery banks (12V, 24V and 48V) Very simple ‘Plug and Play’ installation Perfect integration with Enerdrive DC Modular products The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4). The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit. Enerdrive Accessories Box with ePro Plus Battery Monitor and Switches, Not Pre-Wired: The Enerdrive Accessories Box comprises of an ePRO Plus Battery Monitor, three switches and the provision to mount your battery monitor display. If you choose to purchase the board with the accessories box, the accessories box will be included in your package but not mounted and not pre wired. There is a space on the board to mount the accessories box, or you may want to mount it elsewhere in your vehicle.
Read more